Answer:
Collision insurance coverage
Explanation:
This type of coverage will pay to repair or replace the car if a damage is acquired in an accident with another vehicle or an object such as a building, a tree or a fence.
It is normally a requirement by the lender. It covers the following;
Collision with another vehicleCollision with an object/ a tree / a fenceA single car accident that experienced a rolling or a falling overAny help is appreciated.
PLEASE HELP
Which of the following identifies how an engineer includes interior designs?
A crisscross replica is made of the design prototype to show the interior view.
An internal view is used by scaling a drawing to the exact dimensions.
A sketch is included to show interior designs using a technique called sectioning.
An internal design is not necessary until a machinist has created the design.
Answer:
A sketch is included to show interior designs using a technique called sectioning.
Explanation:
In order to identify interior designs, an engineer includes a sketch to show interior designs using a technique called sectioning.
Sectioning is a technique used in engineering drawings to illustrate a structure as if it has been divided along another imaginary plane or cut into halves such as a vertical or horizontal plane. This technique is usually used by engineers and architects to show the details of the component and interior design of an object.
Hence, sectioning helps to give a view of the hidden part of an object through a cutting plane.
Answer:
A sketch is included to show interior designs using a technique called sectioning.
Explanation:
Provide the 4 sequence process of a 4-stroke engine?
Answer:
NH4)2Cr2O7(s)→Cr2O3(s)+N2(g)+4H2O(g
EXPLATION
NH4)2Cr2O7(s)→Cr2O3(s)+N2(g)+4H2O(gNH4)2Cr2O7(s)→Cr2O3(s)+N2(g)+4H2O(g
According to the video, what qualities do Information Technology workers need? CHECK ALL THAT APPLY.
physical strength and fitness
a logical and methodical mind
social awareness
creativity
mental agility and flexibility
confidence
Answer:
B.) a logical and methodical mind
D.) creativity
E.) mental agility and flexibility
Explanation:
According to the video,the qualities do Information Technology workers need a logical and methodical mind,creativity and confidence.
What is the information technology career?Information technology (IT) professionals are known to be people who functions by helping firms to handle or maintain their digital infrastructure. They also help to give troubleshooting assistance to technology consumers and thus this kind of people needs to be creative and has a flexible mind.
A general contractor otherwise known as the prime contractor is responsible for the day-to-day oversight of a construction site, employment of labour, management of vendors and trades, and most importantly, the communication of information to all involved parties throughout the course of a building project.
Therefore, According to the video,the qualities do Information Technology workers need a logical and methodical mind,creativity and confidence.
Learn more about Information Technology on:
https://brainly.com/question/29244533
#SPJ6
Need help with these ez questions will mark brainiest
Hi! Here's the answers!
True
C
True
Answer:
True, C, True.
Explanation:
A. True - In order to give appropriate feedback you have to listen
B. C - Employability skills are things that you would be hired and expected for and expected to continue using throughout your job.
C. True - Thinking critically and solving problems are transferable job skills.
Hope this helps :)
What problem of the low-bid process is the negotiated price process intended to solve?
O The negotiated price process places a greater emphasis on lowering cost than the low-bid process.
The negotiated price process focuses on contractor qualifications instead of simply seeking the lowest-bidding contractor.
O The negotiated price process is easier to manage than the low-bid process.
O The negotiated price process is faster than the low-bid process.
Answer:
D
Explanation:
.
Answer:
The negotiated price process focuses on contractor qualifications instead of simply seeking the lowest-bidding contractor.
Explanation:
I took the test
Need help with this question pls help me will mark brainiest
Need help with these 2 ez questions pls help me will mark brainiest
Answer:
16.) yes
17.) critical thinking
Explanation:
Thanks to anyone who helps!
In your own words, describe each of the following terms: Science, Technology, Engineering, and Math
Answer:
Science is the study of our nature and natural things to gain knowledge about them.
Technology is when we use the scientific knowledge acquired to apply it in life.
Engineering is a branch of science and technology involved in the design and building of structures and machines.
Math is the knowledge of numbers , shapes and patterns.
Explanation:
In science we study subjects such as biology , chemistry and physics. When we study science we gain new knowledge, we improve our education and increase our standard of living. Galileo Galilei was the father of science who linked theory explanations with an experiment. Technology is the application of the scientific knowledge in industries, equipment development or day to day activities. Here, skills, methods and processes will be applied to achieve objectives, offer service or create a good. Engineering is applies concepts in science and technology including math to come up with designs for machines, structures and systems that solve challenges in the environment. Engineers use their technical skills to critically build things that improve the lives of people. In math, people learn logic of shapes, quantity and arrangement. Math is everything around us.
What will happen to the aircraft speed if the drag force becomes more than the thrust force ? Help
Answer:
Explanation:
If the forces of thrust and drag are balanced, an aircraft doesn't move. It is only when thrust overcomes drag that a plane moves forward. When drag is greater than thrust, the plane is pushed backward,
please
Brain-list it or support me at my U-Tube channel " ZK SOFT&GAMING " I will be thankful
Match the task to the required education level.
classifies wildlife around a geothermal plant,conducts environmental impact studies of geothermal plants, and analyzes the distribution and movement of water at a geothermal plant site.
masters degree, bachelors degree, and doctorate degree.
Answer: See explanation
Explanation:
For a bachelor's degree, one takes several subjects or courses that relates to one's main course. For a master's degree, one focuses on his or her main course while a doctorate degree is usually research based. Based on the explanation, the question is answered below.
• Classifies wildlife around a geothermal plant = Bachelor degee
A bachelor's degree is required here as it doesn't involve research and it just involves an easy classification.
• Conducts environmental impact studies of geothermal plants = Masters degree
This relates to one major aspect which is regarding geophysics. Hence, the Masters degree is appropriate.
• Analyzes the distribution and movement of water at a geothermal plant site = Doctorate degree
This is highly researched based, hence the doctorate degree will be vital.
Will the ABS system activate when you push on the brake pedal at 25MPH? Yes/No
A faulty _______________ will allow gear lube to saturate brake shoes in a rear drive vehicle.
What is the term used to describe how large the inside diameter of a drum can be before it must be replaced?
20 points
Answer:
yes
Explanation:
Need help with these 3 ez questions pls help me will mark brainiest.
Answer:
13. time management
14. unprofessional behavior
15. soft skills
What are watts equal to?
newton-meters
joules per secon
meters per seconds
newtons per meter
Answer:
joules per second
equivalent to one ampere under a pressure of one volt.
Experts see the period immediately prior to the advent of World War II as the beginning of the modern residential construction industry in
the United States.
O True
O False
Answer: false
Explanation: got it right
Which tool would be best for measuring out and creating multiple versions of the same angle for an octagonal window frame?
Task 2 - Design a leaflet for promoting the 3D CAD modelling
Your supervisor would like to promote the 3D CAD models to Product Design and
Development Department. You are asked to design an A3 sized leaflet for the promotion
use. The topic is "How the 3D CAD modelling can improve the design process in customer's perspectives write pointform not paragraph
This provides evidence for [M3]
please help me
Answer:
I hope it help you
Explanation:
The following points explain well that how can the 3d cad modelling can improve the designing process,
3D CAD drawings allow for swift modifications and engineering changes with alterations to 3D models versus 2D drawings. This results in greatly enhanced revision control during the product design process. This enables quick customization of standard products to meet market demands and specific customer needs.Save progress and designs easily.We can get Better visualization.3D modeling brings a project to life without even moving a single speck of dust! 3D modeling in construction also allows animation which is very help full.Naturally, the client can visualize so much more about an upcoming project that a flat drawing could ever provide.please
Brain-list it or support me at my U-Tube channel " ZK SOFT&GAMING " I will be thankful
What are the use of logic gates in the field of robotics?
Answer:
JESUS IS LORD AND NO ONE CAN GET TO THE FATHER EXCEPT BY THROUGH HIM JESUS IS THE ANSWER.
If the wood needed to lay a kitchen floor was determined to be precisely 287.5 square feet, how much should be purchased
Answer:
316 pieces of wooden floor tiles
Explanation:
From research, the standard size of floor tiles used in kitchen is mostly:
1 ft x 1 ft in dimension.
Now, we are told that the area is precisely 287.5 square feet.
Thus, number of tiles required is;
n = 287.5/(1 × 1)
n = 287.5 tiles
Usually, we make room for 10% wastage.
Thus, we will provide;
N = 287.5 × 1.1
N = 316.25 ≈ 316 pieces of tiles
While discussing the MIL on OBD II systems: Technician A says that the MIL will flash if the PCM detects a fault that would damage the catalytic converter. Technician B says that whenever the PCM has detected a fault, it will turn on the MIL. Who is correct?
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
Answer:
"C"
Explanation:
Answer: c. Both A and B
Explanation: The codes are cleared with a scan tool, Power to the PCM is disconnected and The vehicle is driven on three consecutive trips with a warm up cycle and meets all code set conditions without the PCM detecting any faults.
Technician A says that the oxygen sensor provides the major input during the open-loop mode. Technician B says that the coolant temperature sensor input is not used during open-loop mode operation. Who is correct?
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
Answer:
The correct technician is;
b. Technician B
Explanation:
The closed-loop and open-loop refer to the mode of operation of engines that are fuel-injected based on whether the engine operates based on a feedback signal from an air/fuel ratio sensor which is also known as an oxygen sensor or a lambda so as to regulate the air fuel mixture which is the closed-loop, or whether the engine does not make use of the sensor input for its operation, which is the open-loop mode
Therefore, technician B that says the input of the coolant temperature sensor is not used during the open-loop is more correct as the engine does not make use of a sensor input during open-loop mode, the engine only operates based on the throttle's position.
Answer: b. Technician B
Explanation: Technician B that says the input of the coolant temperature sensor is not used during the open-loop is more correct as the engine does not make use of a sensor input during open-loop mode, the engine only operates based on the throttle's position. The closed-loop and open-loop refer to the mode of operation of engines that are fuel-injected based on whether the engine operates based on a feedback signal from an air/fuel ratio sensor which is also known as an oxygen sensor or a lambda so as to regulate the air fuel mixture which is the closed-loop, or whether the engine does not make use of the sensor input for its operation, which is the open-loop mode
While discussing PCM monitor tests: Technician A says that some monitors only run after another monitor completes. Technician B says that the monitor tests are run when the scan tool activates them. Who is correct?
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
Answer:
D
Explanation:
Answer: d. Neither A nor B
Explanation: A P0401 DTC (exhaust gas recirculation flow insufficient) is being discussed. Technician A says that a defective EGR valve could be the cause. Technician B says that clogged EGR passages could be the cause. OBD-II regulations require that the EGR system be tested. Technician A says that the PCM can monitor the commanded position of the EGR valve to determine if it is functioning correctly. Technician B says that the PCM can open the EGR valve and monitors for a change in the MAP sensor or oxygen sensor reading to detect if the system is functioning correctly.
hello it of JOSPHE BRO DONT ANSWER
Orthographic drawings are used to express ideas that are more complicated. Explain the purpose of the different views and the importance of view alignment
Answer:
Explanation:
Orthographic drawings represent 3D objects using 2D projections.
If you wanted to show what a car looked like and were limited to 2D drawings, you might show a sketch of the front of the car, the side of the car, and the back of the car. These orthographic projects show all the detail of the cars different "sides" effectetly using 2D drawings.
These projections should be aligned such that features of the car can be cross-referenced between different projections.
Answer:
Explanation:
Orthographic drawings represent 3D objects using 2D projections.
If you wanted to show what a car looked like and were limited to 2D drawings, you might show a sketch of the front of the car, the side of the car, and the back of the car. These orthographic projects show all the detail of the cars different "sides" effectetly using 2D drawings.
These projections should be aligned such that features of the car can be cross-referenced between different projections.
What are the success factors for mechanical engineering?
what are the career pathways for mechanical engineering?
What are the learning outcomes for mechanical engineering?
Is there are co op option for mechanical engineering?
How many years in mechanical engineering?
Answer:
1) The success factors are the qualities necessary or required to be able to ) accomplish a mission
The success factors in becoming a mechanical engineer are;
a) The ability to solve complex problems and puzzles that arise in developing mechanical system devices and or products
b) Being creative such as being able to bring about a thing or concept where there is none
c) Have good communication skills for teamwork and when expressing ideas or explaining how a product works
d) Having a teamwork mentality as due to the nature and complexity as well as the need for brainstorming, mechanical engineers frequently work together in groups
e) Having a good understanding of calculus and statistics which are used extensively in mechanical engineering concepts
2) The career pathway for mechanical engineering
a) The career path for mechanical engineering starts with obtaining a degree in mechanical by which an entry level job in the industry
b) Acquiring experience, which is a key aspect to mechanical engineering education and professional career development. Students can learn how to make use of Computer Aided Design (CAD) applications, get internship experience, and take part in projects that require hands-on engagement during their four-year bachelor's degree program in the university
c) Acquiring certifications, such as American Society for Mechanical Engineers (ASME) and American Welding Society (AWS) certification and licenses that show the level of know how, dedication and participation in mechanical engineering
d) When looking for a job it is important to note that employers are mainly interested in an applicant's ability to show hands-on experience and that new engineers usually work under more senior engineers for the first one to four years as they continue to take on increased responsibility
e) Mechanical engineering career advancement by gaining advanced degrees can lead to opportunities that are high-paying
3) The learning outcomes of mechanical engineering are;
Understanding the principles of mathematics, mechanical and electrical engineering and the nature of the integrated process of engineering design as well as develop IT skills
Problem solving and analysis and project management, group project work and specialist mechanical engineering courses
4) Yes there is a co-op option for mechanical engineering
5) Typically four years but in some institutions the program may take five years
Explanation:
Answer:
this is from 2021 man what a time!!!!
Explanation:
Pls help me with these 3 ez questions will mark brainiest
While discussing diagnostic procedures: Technician A says that after the visual inspection has been performed, the DTCs should be cleared from the memory of the PCM. Technician B says that serial data can be helpful when there are no DTCs but there is a fault in the system. Who is correct?
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
Answer:
C the answer is C
Explanation:
yea I hope this helps...
Answer: c. Both A and B
Explanation: Technician A says that knowing if there are any stored diagnostic trouble codes (DTCs) may be helpful when checking for related technical service bulletins (TSBs). Technician B says that only a factory scan tool should be used to retrieve DTCs. Technician A says that reprogramming a PCM using the J2534 system requires a factory scan tool. Technician B says that reprogramming a PCM using the J2534 system required Internet access.
What are examples of Energy careers? Check all that apply. Carpenter Video Editor Electrical Power-Line Installer Printing Press Operator Power Plant Operator Automotive Service Attendant
Answer:
C,E,F
Explanation:
Right on edge 2021
Examples of Energy careers are Electrical Power-Line Installer, Power Plant Operator, and Automotive Service Attendant.
An energy career refers to a career in the energy industry. This can mean the work or jobs related to the energy sector.
A career in the energy industry can be different, ranging from communicators to engineers, specialists, etc. This means that whatever occupation that involves the transfer of energy for consumption are all energy careers. Such types of occupations can be found in numerous sectors that included energy transmission, distribution, and education of such energy for public consumption.Careers in the energy sector require expertise in the transmission, distribution, and education of how to use energy for human consumption. Such careers may include electrical power-line installer, power plant operators, and automotive service attendant.
Learn more about energy careers here:
brainly.com/question/9369455
because the United States is linked to producers distributors and consumers in other countries it is described as participating in a
Answer:
Globalized economy.
Explanation:
The world economy is a global economic system made up of economies of countries that are more or less interconnected. One of the key words in the world economy is globalization, which means that national economies are so closely interlinked that events in one country usually affect the economies of other countries. Globalization has become particularly dominant over the last century. More and more trade is taking place between different countries, and restrictions on this have been significantly reduced. The result is a global economic phenomenon. People can sell goods and services in markets around the world, and consumers can choose from a much wider range of goods and services. It no longer has to be limited to what is offered in one's own country.