A(n) breather vent is used on reservoirs to allow the tank to take in or release air as the fluid level changes during system operation.
Answer:
Vent / Breather Vent
(12 points) a heat exchanger is designed to cool 120 kg/min of water vapor at 2 bar and 400 oc to a saturated liquid at 100 kpa. the cooling water is taken from a local river at an inlet at 5 oc. after passing through a condenser, the temperature of the cooling water is not allowed to exceed 20 oc as regulated by the environmental codes. please determine the minimum mass flow rate of cooling water.
The minimum mass flow rate of cooling water is 66.22 kg/sec.
What is mass?
The quantity of matter in a physical body is defined as mass. It also represents the body's inertia, or resistance to acceleration whenever a net force is applied. The mass of an object dictates the strength of its gravitational attraction to certain other bodies. The kilogramme is the SI base unit of mass.
At 2bar 400° c
Specific enthalpy h₁=3276.88 k3/kg.
At 100Kpa
Saturated liquid h₂= 504.684
ΔT= 20° c
Energy balance,
AT=201 (cooly water)
Heat loss by vapour = Heat gain by water
120/60 (3276.98-504.684) = mw X4.186 (20)
mw= 66.22 kg/sec.
To learn more about mass
https://brainly.com/question/19385703
#SPJ4
position for an electron is 4.7i - 4.1j + 5.7k find the magnitude
Answer:
for the magnitude we use Pythagoras (with the components) to get: ∣∣∣→A−→B∣∣∣=√(−1)2+(5)2=√1+25=√26≈5.1
The point in an electrical circuit schematic where high
voltage is stepped down to low voltage is at what
component?
Select one:
O A. Contactor
O B. Solenoid
O C. Relay
O D. Transformer
The point in an electrical circuit schematic where high voltage is stepped down to low voltage is at transformer.
What do you mean by an electric circuit?
Path for transmitting electric current in an electric circuit. An electric circuit consists of a device that provides energy to the charged particles that make up current, such as a battery or a generator, as well as devices that use current, such as lamps, electric motors, or computers, and the connecting wires or transmission lines. Ohm's law and Kirchhoff's rules are two fundamental laws that quantitatively define the behaviour of electric circuits.
Step-down transformers are used to connect transmission lines with varying voltage levels. They reduce the voltage level from a high to a low value.
So, D is the right answer.
To learn more about electric circuit
https://brainly.com/question/19651288
#SPJ13
When developing the light bulb, thomas edison’s lab went through numerous materials until they found one that would work. Which one finally worked?.
Platinum filament.
Thomas Edison went through a series of different experiments while developing bulb until and unless the electricity passed through the Platinum filament, and it finally worked.
You can learn more about Bulb development through the link below:
https://brainly.com/question/14016925#SPJ4
A secondary needle will not be on an indicator with which kind of measurement scale?
Long range
O Short range
Full
Balanced
Answer:
The correct answer would be interval in short range
Explanation:
list any four styles of lettering
Answer:I know more than 4
Explanation:
Traditional calligraphy. Calligraphy is the design and creation of hand lettering with a brush or other writing tool. ...
Gothic lettering. ...
Modern calligraphy. ...
Serif lettering. ...
Sans serif lettering. ...
New lettering styles.
8. SAI and IA are most useful for what?
OA. Correctly measuring the front wheel track
OB. Evaluating the exact caster setting needed
OC. Determining if the setback is correct
OD. Determining if there has been collision damage
Grade/Exit
Return. The steering pivot line's angle, as seen from the front of the vehicle, is known as the steering axis inclination (SAI). When you turn the wheel away from a straight forward position, the vehicle lifts slightly due to the included angle, which is created by adding this angle to the camber (see below).
What is Sai's primary motivation?The Steering Axis Inclination (SAI) angle causes the wheel spindle to slant downward slightly as the wheel is turned, which directly affects steering and handling. The same effect is produced by caster, which is the forward or backward tilt of the steering axis as seen from the side. How is the Student Aid Index going to be determined? Your SAI is based on the financial profile of you and your family as described in the Free Application for Federal Student Aid, or FAFSA. The index will be equal to the total of your income, your parents' income, and your assets.
To learn more about 'SAI and IA' refer to
https://brainly.com/question/14432232
#SPJ1
The steering pivot line's angle, as seen from the front of the vehicle, is known as the steering axis inclination (SAI).
What is Sai's primary motivation?The Steering Axis Inclination (SAI) angle causes the wheel spindle to slant downward slightly as the wheel is turned, which directly affects steering and handling. The same effect is produced by caster, which is the forward or backward tilt of the steering axis as seen from the side. Your SAI is based on the financial profile of you and your family as described in the Free Application for Federal Student Aid, or FAFSA. The index will be equal to the total of your income, your parents' income, and your assets.The steering axis inclination is the angle of the steering pivot line as seen from the front of the car. The included angle, which is produced by adding this angle to the camber, causes the vehicle to lift slightly when you turn the wheel away from a straight forward position.To learn more about 'Steering Axis Inclination' refer to
https://brainly.com/question/29210922
#SPJ1
Technician A says that weld on attachments may be used on a steel panel. Technician B says that glue on attachments may be used on a steel panel
For joining the attachments on the steel panel both the options such as welding and gluing are prevalent and highly useful.
Welding is considered an excellent procedure to join the thin sheet attachment of a steel panel. The type of welding used for joining the attachments on steel surfaces is typically called tack welding. Tack welding performs very small welds that do not cause any damage to the surface of the steel panel. Hence, technician A is correct who states that on a steel panel, welding may be used on attachments.
Similarly, attachments on the steel materials have the option to be joined with glues. Cyanoacrylate-based adhesives and polyurethane-based glues are considered best to provide the strong joining of attachments as welding. Therefore technician B is also correct who says that glue may be used on steel panels to join attachments. It is because on a steel surface glue cannnot be useable as it is not able to join attachments.
Since both welds and glues can work on steel material in order to join attachments, both technicians are correct.
You can learn more about steel at
https://brainly.com/question/28221478
#SPJ4
what does '' emerging'' mean, emerging technologies and how are they found?
Answer:
The term commonly refers to technologies that are currently developing, or that are expected to be available within the next five to ten years, and is usually reserved for technologies that are creating, or are expected to create, significant social or economic effects.
The result is the delineation of five key attributes that qualify a technology as emerging. These are: (i) radical novelty, (ii) relatively fast growth, (iii) coherence, (iv) prominent impact, and (v) uncertainty and ambiguity.
In developing engine designs, manufacturers use thermocouples to measure the ___________ of components, such as spark plugs and exhaust systems.
Answer: High temperatures
Technician A says that all-wheel drive vehicles are the same as four-wheel drive vehicles. Technician B says that front-wheel drive drivetrains are the most common on cars today. Who is correct?
According to the question, Technician B is correct because he said that front-wheel drive drivetrains are the most common on cars today.
What is the responsibility of the technician?The responsibility of the technician includes analysis and service of the system, diagnosing the actual problems, performing troubleshooting, testing and running of equipment, repairing or replacing faulty or damaged equipment, etc.
According to the context of this question, technician A conveyed that all-wheel drive vehicles are the same as four-wheel drive vehicles. This is actually not accurate and valid. This is because all-wheel drive vehicles are not the same as four-wheel drive vehicles. It significantly depends on the circumference of the wheel.
Therefore, technician B is correct because he said that front-wheel drive drivetrains are the most common on cars today.
To learn more about Technicians, refer to the link:
https://brainly.com/question/18428188
#SPJ1
How does inductive reactance depend on the frequency of the ac voltage source and the rms current through the inductor?.
The gravitational force exerted on a solid object is 5N. When the object is suspended from a spring scale and submerged in water, the scale reads 3.50 N. Find the density of the object.
The density of the object is 3333.33 kg/m³. The density of an object is a measure of how heavy it is for a given size, i.e. the mass of material per unit volume.
What is gravitational force?Gravity, also known as gravitational force, pulls objects with mass toward each other. We frequently consider the force of gravity from Earth. This force is responsible for keeping your body on the ground. Any object with mass, on the other hand, exerts a gravitational force on all other objects with mass.
Calculation of density of object?Density: This can be defined as the ratio of the mass of a body to its volume.
The unit of density is kg/m³.
From Archimedes principle,
R.d = W/U = D/D'
Where R.d = relative density, W = weight of the object in air, u = upthrust in water, D = Density of the object, D' = Density of water.
W/U = D/D'
making D the subject of the equation
D = D'(W/U).......................... Equation 1
Given: W = 5.0 N, U = 5.0 -3.5 = 1.5 N, D' = 1000 kg/m³
U = lost in weight = weight in air - weight in water
Substitute into equation 1
D = 1000(5/1.5)
D = 3333.33 kg/m³
Thus the density of the object = 3333.33 kg/m³
To learn more about gravitational force, refer to:
https://brainly.com/question/72250
#SPJ1
Question 2
Salt in crude oil must be removed before the oil undergoes processi
fed to a washing unit where fresh water fed to the unit mixes with t
the sal contained in the oil. The oil (containing salt but no water), be
can be removed at the top of the washer. If the "spent" wash water
oil contains 5% salt, determine the concentration of the salt in the w
crude oil (with salt) to water used is 4:1.
The concentration of the salt in the w crude oil (with salt) to water used is 4:1 is 0.0061.
What is crude oil?
Crude oil is a hydrocarbon mixture that exists in liquid form in natural subterranean reservoirs and stays liquid at atmospheric pressure after passing through surface separation facilities.
The salt content of "spent" wash water is 15%.
5% of crude oil is salt.
The crude oil (with salt) to water ratio utilised is 4: 1.
Crude oil fraction:
95% of crude oil = 0.95
0.95F1 = x1E1
0.95(100) = x1E1
95= x1E1
E1 = 95/X1
wash water fraction:
15% of wash water = 100% -15% = 85%
= F2 = 0.85E2
salts fraction:
0.05F1 = (1-X1)E1 + 0.15E2
0.05F1 = (1-X)95/X1 + 0.15(F2/0.85)
0.05F1 = 95/X1 - 95 + 0.15(F2/0.85) (SINCE = 95.588 = 95/X1 = 99.38)
0.05(100) = 95/X1 - 95 + 17.61(1/4F1)
5 = 95/X1 - 95 + 4.41
Fraction of salts = 1- X1 = 0.0061
To learn more about crude oil
https://brainly.com/question/14260176
#SPJ13
The pyramids in Egypt are cited as an ancient world wonder. What is the main
reason that the pyramids are important to the study of engineering?
The pyramids are important to the study of engineering because they were some of the first structures built using engineering principles. The pyramids are an example of how engineering can be used to create amazing structures.
What is pyramid?
A pyramid is a structure with triangular exterior surfaces that converge to a single step at the summit, giving the shape the shape of a pyramid in the geometric sense. A pyramid's base can be trilateral, quadrilateral, or any polygon shape. A pyramid, as a result, has at least three exterior triangle surfaces. A typical variant is the square pyramid, which has a square base and four triangular exterior surfaces. The design of a pyramid, with the majority of the weight closer to the bottom and the pyramidion at the apex, means that less material will be pushed down from above. This weight distribution enabled early civilizations to build stable massive constructions.
To learn more about pyramid
https://brainly.com/question/218706
#SPJ13
4. Your supervisor texts you during the working hours for no reasons. S/he also invited you for a
dinner to discuss your salary increase issue during a weekend. What should be your role based
on the Ontario's Occupational Health and Safety Act ("OHSA") to deal your supervisor? Discuss.
If your supervisor is texting you during work hours for no reason, you should speak to him or her about it. If your supervisor is inviting you to dinner to discuss your salary increase issue, you should tell him or her that you are not comfortable with that and would prefer to discuss it during work hours. Your supervisor's behaviour is inappropriate and violates the Ontario's Occupational Health and Safety Act ("OHSA"). You should discuss the issue with your supervisor and try to resolve the issue. If you are not able to resolve the issue, you can file a complaint with the Ontario Ministry of Labour.
Occupational Safety and Health Act:
The Occupational Safety and Health Act of 1970 is a United States labour legislation that governs federal occupational health and safety law in the private sector and federal government. Congress passed it in 1970, and President Richard Nixon signed it on December 29, 1970.
To learn more about Occupational Safety and Health Act
https://brainly.com/question/15732592
#SPJ13
In a series RLC circuit, the phase difference between the current in the capacitor and the current in the resistor is?
Answer:
In a series RLC circuit, the phase difference between the current in the capacitor and the current in the resistor is 00 because same current flows in the capacitor as well as the resistor.
Explanation:
a pressure cooker is a pan that cooks food much faster than ordinary pans by maintaining a higher pressure and temperature during cooking. the pressure inside the pan is controlled by a pressure regulator (the petcock) which keeps the pressure at a constant level by periodically allowing some steam to escape, thus preventing any excess pressure buildup. a certain pressure cooker has a volume of 6 l and an operating pressure of 75 kpa gage. initially, it contains 1 kg of water. heat is supplied to the pressure cooker at a rate of 500 w for 30 min after the operating pressure is reached. assuming an atmospheric pressure of 100 kpa, determine: a) the temperature at which cooking takes place. b) the amount of water left in the pressure cooker at the end of the process. assume some liquid water is still in the pan.
More cooking is done before the water actually begins to boil thanks to the raised pressure inside the cooker, which raises the boiling point of water above 1000C. In the end, food cooks more quickly.
Slow-cooked meals can be quickly prepared with pressure cookers. They are efficient in terms of electricity consumption and are excellent for tenderizing less expensive portions of meat. They are a healthy cooking method since they effectively retain nutrients and can cut cooking times by up to 50%. Water boils at 121°C (250°F) at that pressure. As a result, food may cook at considerably greater temperatures than it could under atmospheric pressure. Additionally, because cooking reactions quicken at higher temperatures, food cooks more quickly it is a good technology.
Learn more about consumption here-
https://brainly.com/question/13439091
#SPJ4
What is defining feature of the meta verse?
The defining feature of the Metaverse is that it is Virtual. This is its a most distinctive feature. See further details below.
What more do we know about the Metaverse?The Metaverse does not compete with the internet; rather, it expands upon it.
Users navigate a virtual environment that duplicates features of the actual world utilizing technologies such as virtual reality (VR), augmented reality, artificial intelligence (AI), social media, and digital money in the metaverse.
Metaverse features include digital avatars, remote working, developing decentralization, hardware, encryption, and many more.
Similarly, virtual places like Zoom only allow for a single conversation. Participants at physical events can transition seamlessly from one talk to the next. Some colleges are utilizing metaverse technology to bypass internet and video meeting tool constraints.
Learn more about the Metaverse:
https://brainly.com/question/5513926
#SPJ1
how is the efficiency of cooling equipment measured? is using integrated part load values a good way to define the efficiency of large cooling equipment ? why or why not
The EER is a metric for how effectively an air conditioning system can cool a space per unit of power used. It is computed by dividing the amount of cooling capacity an AC delivers per hour by the watts of electricity used.
To determine an air conditioner's EER, measurements taken on the warmest day of the year are often used. EER, in its simplest form, aims to provide consumers with a sense of the cooling power they may anticipate from an AC for every dollar spent on electricity.
Ratio of Seasonal Energy Efficiency (SEER)
SEER provides the average efficiency for the entire season, making it a more dependable efficiency rating for air conditioners than EER, which only assesses the energy efficiency of the AC on the hottest day of the season. It is calculated by dividing the AC's output power (measured in BTUs) over the course of a season by the total energy the machine used during that same period.
Developed by the EPA, this efficiency rating is well-known. The performance and energy efficiency of HVAC systems with the Energy Star rating are often tested to see if they can provide consumers with excellent value while helping to reduce national energy consumption. Although some gadgets cost a little bit more than their less efficient equivalents, the price difference can easily be made up for in energy savings over time.
To know more about EER click on the link:
https://brainly.com/question/15140663
#SPJ4
Let's consider the case when we increase the number of elements to 5. How many temperature values will we need to obtain to determine the variation of temperature along the line?
We have a total of 6 nodes with 5 components. We must determine the temperature at each of these six nodes. Mesh refining is the process of increasing the number of elements.
What is temperature?
Temperature is a scientific term that describes how hot or cold something is.There are three types of temperature scales: those described in terms of the average translational kinetic energy per freely moving microscopic particle in a body, such as an atom, molecule, or electron, such as the SI scale; those which rely solely on purely macroscopic properties as well as thermodynamic principles, including such Kelvin's original definition; and those that are not defined by theoretical principles, and yet are defined by convenient empirical properties of particulate matter.
To learn more about temperature
https://brainly.com/question/2339046
#SPJ13
Technician A says that water fade changes the coefficient of friction between the brake linings and drums until they dry out. Technician B says that hydraulic fade is caused by brake caliper seals leaking fluid onto the rotors. Who is correct?
According to the given question, technician A is correct.
Who are technicians?
A technician is a worker in a technological field who is skilled in the relevant skill and technique and has a practical understanding of the theoretical principles. Technicians are highly skilled professionals who work in nearly every industry. They service, repair, install, and replace various systems and equipment. Technicians typically work in teams with other skilled workers and must be able to read and communicate effectively.
Water fade occurs as a result of water-soaked brake linings acting as a lubricant, lowering the coefficient of friction between the braking surfaces. And technician A says that water fade changes the coefficient of friction between the brake linings and drums until they dry out.
So technician A is correct.
To learn more about technician
https://brainly.com/question/18428188
#SPJ9
what is dbr in om???
The debt-burden ratio (DBR), which includes loan and credit card payments, is the ratio of your total monthly expenses to your gross income.
How is DBR determined?Your debt-burden ratio (DBR), which includes payments for loans and credit cards, is the proportion of your total monthly expenses to your gross income. Banks use this figure to determine your eligibility for loans and credit cards because it reflects your present debts and repayment capacity.While dBm expresses the absolute power level, dB quantifies the ratio between two values. dBm is a dimensionless unit, whereas dB is an absolute unit. While dB is represented in watts and can be relative to various powers, dBm is always relative to 1mW.Your debt-burden ratio (DBR), which includes payments for loans and credit cards, is the proportion of your total monthly expenses to your gross income. Banks use this figure to determine your eligibility for loans and credit cards because it reflects your present debts and repayment capacity.DBR scheduling assists custom manufacturers by locating the resource in a shop that is causing delays, and then builds a plan around that resource to improve the efficiency and performance of the entire shop.To Learn more About dBr, Refer:
https://brainly.com/question/17562254
#SPJ1
What transfers the up-and-down motion from the lifter to the
rocker arm
Answer:
Explanation:
The camshaft lobe moves the lifter upwards, which moves the pushrod. The top end of the pushrod pushes on the rocker arm, which opens the valve.
The manager of a small post office is concerned that the growing...
The manager of a small post office is concerned that the growing township is overloading the one-window service being offered. Sample data are collected on 100 individuals who arrive for service:
TIME BETWEEN
ARRIVALS (MINUTES) FREQUENCY
1 5
2 32
3 35
4 19
5 9
100
SERVICE TIME
(MINUTES) FREQUENCY
1.0 12
1.5 21
2.0 36
2.5 19
3.0 7
3.5 5
100
Using the following random number sequence, simulate six arrivals (Hint: Use random number set from 00 to 99.)
RN: 93, 5, 53, 20, 10, 45, 67, 55, 92, 75, 41, 46, 58, 82, 20, 97, 13, 36
a. Average customer waiting time, in minutes (Round your answer to 4 decimal places.)
Average customer waiting time minutes
b. Average percent idle time for clerks.
Average percent idle time
Answer:
its b
Explanation:
The potential energy of a roller coaster is 50 joules. The kinetic energy of the same coaster is 50 joules. What is the mechanical energy of the coaster?.
The mechanical energy of the coaster is 100 Joules.
What is mechanical energy?
Mechanical energy is equal to the sum of potential and kinetic energy. The principle of mechanical energy conservation asserts that if an isolated system is subjected to solely conservative forces, the mechanical energy is constant. If an object moves in the opposite direction of a conservative net force, its potential energy increases; and if the item's speed (not velocity) changes, so does its kinetic energy.
Substituting the given parameters into the formula, we have;
Potential energy of roller coaster = 50 Joules.
Kinetic energy of roller coaster = 50 Joules.
So,
M.E= 50+50
Mechanical energy (M.E) = 100 Joules.
Therefore, the mechanical energy of the roller coaster is 100 Joules.
To learn more about mechanical energy
https://brainly.com/question/2856050
#SPJ4
Briefly explain thermal expansion using the potential energy–versus–interatomic spacing curve.
As the temperature of the material increases, the potential energy of the molecules increases. Thermal expansion occurs due to changes in temperature, and interatomic distances increase as potential energy increases.
What are the uses of Thermal Expansion?Thermal expansion is used in a variety of applications such as rail buckling, engine coolant, mercury thermometers, joint expansion, and others.
It is to be noted that an application of the concept of liquid expansion in everyday life concerns liquid thermometers. As the heat rises, the mercury or alcohol in the thermometer tube moves in only one direction. As the heat decreases, the liquid moves back smoothly.
Learn more about Thermal Expansion:
https://brainly.com/question/1166774
#SPJ1
